Rca RMB-167 Manuel d'utilisateur

RMB-167USER’S GUIDEVersion 1.0July 1998RIGEL CORPORATIONP.O. Box 90040Gainesville, Florida 32607(352) 373-4629www.rigelcorp.com

- -43 START-UP3.1 Connections, Jumper Settings1. Connect your RIGEL board to the PC host via a serial cable.2. Connect the board to a power supply.

- -5 2. Open the TTY window using the Tools | TTY menu command. Select the communicationport parameters using the Tools | TTY | TTY Options menu

- -6RMON16x. Once the monitor program is loaded, the monitor commands are available to theuser.1. Press the reset button on the board.2. From the

- -73.7 TroubleshootingAll the boards are functionally tested before shipment. If the system does not bootstrap asexpected, review the hardware, sof

- -84 OPERATING NOTESThe RMB-167 needs two connections: to a 5 volt well regulated power supply and to the serialport of a host via a modem cable.4.1

- -95 MEMORY OPTIONSThe RMB-167 memory decoding is accomplished by two 16V8-type GAL devices, U1 and U2.Both devices are collectively responsible of

- -10Address RangeJumpersinserted0-7FFFh 8000h-FFFFhnone RAM RAMCFG0 EPROM RAMCFG1 RAM EPROMCFG0 andCFG1EPROM EPROMThe EPROM at low memory may contai

- -11; --- !!! ASSUMES 8000h-FFFFh is RAM !!! ---; org 08000hcmdbuf equ 08000hpbuffr equ 08020h;------------------------------------

- -12; mov SYSCON, #0F800h; SYSCON is 89h on the 167 dw 089E6h dw 0F800h nop; mov SYSCON, #0F800h; SYS

- -136 GAL EQUATIONSTwo PALCE16V8 are used. The first (U1) is responsible for the reset logic and auxiliary options,and the second (U2), for the mem

(C) 1998 by Rigel Corporation. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, ortransmitted in any

- -146.1.2 U2 Equations; U2 Memory Decode Logic;----------------- PIN Declarations ---------------; --- inputs ---PIN 1 A0 COMBI

- -15COMPANY Rigel CorporationDATE 07/20/94CHIP _r167u1 PALCE16V8; --- PIN Declarations --------------------------------; --- inputs ---PIN 1

- -16; --- PIN Declarations --------------------------------; --- inputs ---PIN 1 A0 COMBINATORIALPIN 2 A14 COMB

- -177 HEADERS AND JUMPERS7.1 System and I / O HeadersThe RMB-167 board has three headers, two of which are compatible with those of the RMB-166.The

- -18Note that pins 46-50 on the RMB-167 are not connected to any signal.JP7 - Input/Output HeaderSignal Pins SignalRMB-166(JP2)RMB-167(JP7)RMB-166(J

- -19 JP8 - Extra Input/Output Header of the RMB-167Signal Pins SignalRMB-167 RMB-167Ground 1 2 VCC (+5V)Ground 3 4 VCC (+5V)P6.0 5 6 P6.1P6.2 7 8 P6

- -207.2 Analog-to-Digital Converter Reference JumpersThe analog-to-digital converter requires a ground and reference voltage. These referencevoltag

- -218 BOOTSTRAPPINGThe RMB-167 bootstrapping is triggered by grounding P0L.4 at reset. A 16 pin header is used toground the bits of P0L via a resis

- -22Note that the NOP (no operation) operations are required to fill the 32 bytes, since the bootstraploader remains active until all 32 bytes are r

- -23respectively. The code within the 604-byte download block pokes these bytes starting fromaddress 0. That is, these instructions are placed int

- -249 THE MINIMAL MONITORThe minimal monitor is placed by the bootstrap loader starting at address 8000h. The monitorresponds to two single-letter

- -259.1 MON167 MonitorThe monitor program RMON167 allows inspecting and modifying the first 64K segment of RMB-167 memory, configuring the ports,

- -26P Port DataThe P command is used to read from or write to the ports. Pn displays the current value of port n.If port n is an input port, then t

- -2710 READS166 VERSION 3.0READS166, version 3.00, is Rigel Corporation’s Integrated Development Environment for theSGS Thomson 16-bit processors.

- -28By using the long names provided by the 32-bit Windows operating systems, you may use thisfeature to keep different versions of your software in

- -2911 CIRCUIT DIAGRAMS

WARRANTYRIGEL CORPORATION - CUSTOMER AGREEMENT1. Return Policy. This return policy applies only if you purchased the RMB-167 evaluation board directl

Table Of Contents1 OVERVIEW ...

10.1.1 Project ...

1 OverviewThe RMB-167 is an evaluation board for the Siemens SAB C167 microcontroller. The RMB-167board accepts the following processors, the SAB C16

- -2RMON166 - The READS166 monitor programRMON 166 is downloaded after bootstrapping (or it may be placed into ROM) and supports basicmemory and por

- -32 SOFTWAREThe RMB-167 board comes with software from Rigel Corporation and third party vendors, whomwe work very closely with. Rigel’s own softw